How to Repair Bifold Door Top Roller Guide

If your bifold doors have become stuck and squeaking, they may require a little attention. It is possible that you need to clean, lubricate or adjust them. The problem may be caused by an unfastened screw on the top pivot or by the top roller guide.

This kit includes all the hardware you require to restore your bi-fold door repair wardrobe door system to its peak performance.

Remove the Door

It might seem difficult and difficult to install the bifold internal doors however for those who are DIYers with some experience, it's actually quite easy. The frame is not the problem, but getting the doors to close and fold smoothly is. Bifold doors are intricate pieces of machinery and, as such, they might need some tuning up to function correctly. This could be as easy as tightening a screw or as complex as taking out the door and [Redirect Only] replacing a pivot pin or roller.

You can usually resolve these issues with a few simple adjustments, without the need to take off the doors. You may find that your doors are sagging or scratching the floor, or that they are bouncing off of their track. It's not difficult to fix these issues. Follow these three easy steps and your bifold door should be back in track in short time.

The most common issue internal bifolding doors encounter is that they are sliding out of alignment. This can be due to loose screws, holes on the anchor/pivots or an unaligned bifold door. In the majority of cases, you can correct this issue with a few simple adjustments, but if the door isn't moving at all it could be necessary to have it removed and replaced.

You'll have to take off the door with a screwdriver, and possibly a pair pliers to loosen any pivot pins that are too tight. The screwdriver can be used to break any locking levers on the bottom pivot bracket and the pliers will allow you to wiggle the pin out and off.

When the top roller is loose it should be possible to raise the door and swivel it downwards in order to lift it off its track and pivot brackets. It's usually a straightforward procedure, but be careful to not let the door strike the door frame. You should then be able cut off the edge of the door which is scraping the floor, and sand it down until it's smooth. You can then paint or refinish the door if needed.

Take off the Roller Guide

This spring-loaded guide roller is mounted on the top of a bifold door to help in smooth operation. It is made specifically for Kenna frames and will fit door panels that range from 1 inch to 1-3/8 inch thick. It is constructed of steel, nylon, and plastic components. It will replace the damaged guide.

To begin to remove the roller guide, remove any screws holding it in place using an screwdriver as well as a bit to loosen it. Use your hands to carefully pull it from the frame. It might require some effort to take off the door, so make sure you ask someone else to assist you.

Once the guide you used to guide your child is removed, carefully cut through the remaining finish over the foot of the new guide with a razor blade to cut it off from the rod blank. This will make it easier to remove and will prevent damage to the new guide foot. Be careful when doing this as the foot is extremely sharp and could potentially cut or nick your fingers.

You may have to apply a little force to pull the guide off, but take care not to chip or break the foot. After removing the guide, you must remove any threads or epoxy left in the place where it was attached. This will help prevent any future issues with the guide.

After removing the guide, test your replacement by placing it at its permanent position. Make a few turns with masking tape or guide tubing in order to ensure it stays in place. This will allow you to double check the alignment of the guide and spacing to ensure that everything is properly set up. If you're eyeballing it or using the always accurate CRB Spine Finder and Deflection System it is essential to avoid any problems in the future.

The final step is to replace the door. If the guide is in the right position and is working just as it should, you're able to proceed. Make sure to replace and tighten any screws or pins that you removed or loosen.

Take the Bottom Pivot off.

repair bifold door bottom pivot doors are a stunning addition to any home but sometimes they need a little tweaking or adjustment to remain in good shape. Some issues can be resolved with the doors in place. Other issues will require the doors be removed. This guide will guide you through the process of removing internal bifold pivots for doors and rollers, as well as pins and pins, to get your doors sliding like new.

Gathering your tools is the first step. Putting everything together before time can save you some frustration later on in the project. You'll need a screwdriver, pliers and maybe a wrench. You can purchase a set of basic tools at your local hardware store for a reasonable price. It's recommended to have some wood glue in your kit. This is helpful if you need to put the rollers in the right place.

Once you've collected your tools, begin by opening the bifold doors, and then loosening the top track bracket using your screwdriver. Once the bracket is in place, you should be able to slide the door off of the top track. It could take a little bit of jiggling but it should be able to pop right off the track.

The next step is to remove the bottom pivot from the frame. It is best to do this from the outside of your home, so be sure to close any interior doors you have open. This will make it much simpler instead of working on the inside. If the bottom track is still in good working order you'll be able to simply lift the door and take off the track.

You'll have to replace the track if it's damaged. Hardware stores sell replacement tracks for bifold doors, as well as swinging closet doors. If the track is severely damaged, then you might need to replace it entirely.

After your track has been repaired or replaced it is time to check the doors for their proper operation. Make sure that they are easily able to move between positions. You'll need to ensure that the edges of your door are parallel to the frame when it is closed. If they're not, you'll need to adjust the top pivot bracket while tightening or loosening the bottom screwscrew.

Replace the Roller

If they are installed correctly, bifold doors can neatly enclose laundry nooks, pantries and closets. Bifold doors comprise two panels that are hinged and slide on an incline at the top of the frame. Over time the roller guide bearings could wear out, causing the doors to bow and rub against the floor. The guide roller can be replaced in just a few minutes using a few tools.

The first step is removing the guide roller from your door panel. The bolt that holds the bottom pivot is to be removed, as well as the screw holding the guide to the top of the door panel needs to be loosen. After the guide is removed and the door panel is lifted up and off its track. Then using a wrench remove the top pivot bolt from the hole in the frame's header by loosening the bolt.

Stanley, Cox and Acme offer a replacement top nylon roller that has a 7/8-inch diameter wheel mounted on a base made of steel. It is mounted on the top of bifold doors that range from 1 inch to 1-3/8 inches thick and comes spring-loaded to self-adjust in the upper track for smooth gliding.

Bifold doors can also scrape against the floor as it closes and opens. This can happen after installing carpet or other flooring materials that require the doors to be raised slightly to allow for adequate clearance. The removal of the bottom pivot adjustment screw and loosening the top track's mounting screws, and moving the anchor/pivot pin is typically enough to eliminate this issue.

A new set top roller guides is a cost-effective solution to the problem of your bifold doors being difficult to operate. They are usually available at the hardware store near you in the door section but they're also available on the internet from a variety of vendors. In addition to a brand-new top guide for rollers, you'll require a small bottle of Elmer's wood glue which is available in big box stores and a squeeze clamp. The clamp is used to keep the repair bifold door top pivot area shut after the glue has been placed in and dried.